| version 1.3, 2006/05/04 02:31:29 |
version 1.8, 2009/11/09 22:51:01 |
|
|
| check_hw_sensors plugin for Nagios monitors sysctl hw.sensors on OpenBSD |
check_hw_sensors - monitors sysctl hw.sensors on OpenBSD |
| check_hw_sensors (-f [<FILENAME>]|(-s <hw.sensors id> -w limit -c limit)) |
check_hw_sensors [-i] (-f [<FILENAME>]|(-s <hw.sensors id> [-w limit] [-c limit])) |
| |
|
| Usage: |
Usage: |
| |
-i, --ignore-status |
| |
Don't automatically check the status of sensors that report it. |
| -f, --filename=FILE |
-f, --filename=FILE |
| FILE to load checks from (defaults to /etc/sensorsd.conf) |
FILE to load checks from (defaults to /etc/sensorsd.conf) |
| -s, --sensor=ID |
-s, --sensor=ID |
| ID of a single sensor. "-s 0" means hw.sensors.0. |
ID of a single sensor. "-s kate0.temp0" means hw.sensors.kate0.temp0 |
| |
Overrides --filename. |
| -w, --warning=RANGE or single ENTRY |
-w, --warning=RANGE or single ENTRY |
| Exit with WARNING status if outside of RANGE or if != ENTRY |
Exit with WARNING status if outside of RANGE or if != ENTRY |
| -c, --critical=RANGE or single ENTRY |
-c, --critical=RANGE or single ENTRY |
| Exit with CRITICAL status if outside of RANGE or if != ENTRY |
Exit with CRITICAL status if outside of RANGE or if != ENTRY |
| |
|
| -h (--help) usage help |
|
| |
|
| FILE is in the same format as sensorsd.conf(5) plus some additional |
FILE is in the same format as sensorsd.conf(5) plus some additional |
| entries. These additional entries in the file are ignored by |
entries. These additional entries in the file are ignored by |
| sensorsd(8). |
sensorsd(8) this means you can use the same config file for check_hw_sensors |
| |
as well as sensorsd(8). |
| |
|
| check_hw_sensors understands the following entries: |
check_hw_sensors understands the following entries: |
| |
|
| low, high, crit, warn, crit.low, crit.high, warn.low, warn.high |
low, high, crit, warn, crit.low, crit.high, warn.low, warn.high, |
| |
ignore, status |
| |
|
| An ENTRY depends on the type. The descriptions in sensorsd.conf(5) |
An ENTRY depends on the type. The descriptions in sensorsd.conf(5) |
| can be used when appropriate, or you can use the following: |
can be used when appropriate, or you can use the following: |
| |
|
| volts_dc, fanrpm or raw - Anything that includes digits. |
fanrpm, volts_dc, amps, watthour, amphour, integer (raw), percent, |
| Both the value of the check and the value of the sensor |
lux or timedelta - Anything that includes digits. Both the value of |
| response that are not either a digit or period are stripped |
the check and the value of the sensor response that are not either a |
| and then the two resultant values are compared. |
digit or period are stripped and then the two resultant values are |
| |
compared. |
| |
|
| temp - Can be as above, but if the entry has an F in it, |
temp - Can be as above, but if the entry has an F in it, |
| it compares farenheit, otherwise it uses celcius. |
it compares farenheit, otherwise it uses celcius. |
| |
|
| indicator or drive - does a case sensitive match of each |
indicator or drive - does a case sensitive match of each |
| entry in the comma separated list and if it does not match |
entry in the comma separated list and if it does not match |
| any of the entries, it matches the status. |
any of the entries, it sets the status. |
| |
|
| The entries 'crit' or 'warn' (or the -c or -w on the command line) |
The entries 'crit' or 'warn' (or the -c or -w on the command line) |
| may be a RANGE or a comma separated list of acceptable values. |
may be a RANGE or a comma separated list of acceptable values. |
|
|
| |
|
| A RANGE is a low ENTRY and a high ENTRY separated by a colon (:). |
A RANGE is a low ENTRY and a high ENTRY separated by a colon (:). |
| It can also be low: or :high with the other side left blank to only |
It can also be low: or :high with the other side left blank to only |
| make the single check.. |
make the single check. |
| |
|
| check_hw_sensors (nagios-plugins 1.4) 1.14 |
An entry marked "ignore" will cause that sensor to be skipped. |
| The nagios plugins come with ABSOLUTELY NO WARRANTY. You may redistribute |
Generally used with state checking of all sensors to ignore sensors you |
| copies of the plugins under the terms of the GNU General Public License. |
don't care about or that report incorrectly. |
| For more information about these matters, see the file named COPYING. |
|
| |
If you are using --ignore-status, you can still check the status of |
| |
individual sensors with a status entry. |
| |
|
| |
check_hw_sensors v1.26 |
| |
Copyright (c) 2009 Andrew Fresh <andrew@afresh1.com> |
| |
Permission to use, copy, modify, and distribute this software for any |
| |
purpose with or without fee is hereby granted, provided that the above |
| |
copyright notice and this permission notice appear in all copies. |
| |
|
| |
THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES |
| |
WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF |
| |
MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR |
| |
ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES |
| |
WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN |
| |
ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF |
| |
OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. |
![[BACK]](/icons/cvsweb/back.gif){kind=icon}
Return to README CVS log ![[TXT]](/icons/cvsweb/text.gif){kind=icon}
![[DIR]](/icons/cvsweb/dir.gif){kind=icon}
Up to [local] / nagios / check_hw_sensors