Annotation of nagios/check_hw_sensors/sensorsd.conf, Revision 1.7
1.6 andrew 1: # $RedRiver$
1.7 ! andrew 2: # hw.sensors.esm0.temp0=35.00 degC (CPU 1), OK
! 3: # hw.sensors.esm0.temp1=35.00 degC (CPU 2), OK
! 4: # hw.sensors.esm0.temp2=29.00 degC (Mainboard), OK
! 5: # hw.sensors.esm0.temp3=22.00 degC (Ambient), OK
! 6: # hw.sensors.esm0.temp4=30.00 degC (Backplane Top), OK
! 7: # hw.sensors.esm0.temp5=30.00 degC (Backplane Bottom), OK
! 8: # hw.sensors.esm0.fan0=3828 RPM (Fan 1), OK
! 9: # hw.sensors.esm0.fan1=4011 RPM (Fan 2), OK
! 10: # hw.sensors.esm0.fan2=3662 RPM (Backplane Fan 1), OK
! 11: # hw.sensors.esm0.fan3=3514 RPM (Backplane Fan 2), OK
! 12: # hw.sensors.esm0.fan4=3475 RPM (Backplane Fan 3), OK
! 13: # hw.sensors.esm0.fan5=3784 RPM (Power Supply 1 Fan), OK
! 14: # hw.sensors.esm0.fan6=3478 RPM (Power Supply 2 Fan), OK
! 15: # hw.sensors.esm0.fan7=3120 RPM (Power Supply 3 Fan), OK
! 16:
! 17: # hw.sensors.esm0.fan8=0 RPM (Fan 1), CRITICAL
! 18: hw.sensors.esm0.fan8:ignore
! 19: # hw.sensors.esm0.fan9=0 RPM (Fan 2), CRITICAL
! 20: hw.sensors.esm0.fan9:ignore
! 21: # hw.sensors.esm0.fan10=0 RPM (Fan 3), CRITICAL
! 22: hw.sensors.esm0.fan10:ignore
! 23: # hw.sensors.esm0.fan11=0 RPM (Fan 4), CRITICAL
! 24: hw.sensors.esm0.fan11:ignore
! 25: # hw.sensors.esm0.fan12=0 RPM (Fan 5), CRITICAL
! 26: hw.sensors.esm0.fan12:ignore
! 27: # hw.sensors.esm0.fan13=0 RPM (Fan 6), CRITICAL
! 28: hw.sensors.esm0.fan13:ignore
! 29:
! 30: # hw.sensors.esm0.volt0=1.65 VDC (CPU 1 Core), OK
! 31: # hw.sensors.esm0.volt1=1.66 VDC (CPU 2 Core), OK
! 32: # hw.sensors.esm0.volt2=4.98 VDC (Motherboard +5V), OK
! 33: # hw.sensors.esm0.volt3=11.95 VDC (Motherboard +12V), OK
! 34: # hw.sensors.esm0.volt4=3.23 VDC (Motherboard +3.3V), OK
! 35: # hw.sensors.esm0.volt5=2.49 VDC (Motherboard +2.5V), OK
! 36: # hw.sensors.esm0.volt6=1.50 VDC (Motherboard GTL Term), OK
! 37: # hw.sensors.esm0.volt7=2.90 VDC (Motherboard Battery), OK
! 38: # hw.sensors.esm0.volt8=4.97 VDC (Backplane +5V), OK
! 39: # hw.sensors.esm0.volt9=12.06 VDC (Backplane +12V), OK
! 40: # hw.sensors.esm0.volt10=2.83 VDC (Backplane Board), OK
! 41: # hw.sensors.esm0.volt11=4.70 VDC (Backplane SCSI A External), OK
! 42: # hw.sensors.esm0.volt12=4.78 VDC (Backplane SCSI A Internal), OK
! 43:
! 44: # hw.sensors.esm0.volt13=5.07 VDC (Power Supply 1 +5V)
! 45: hw.sensors.esm0.volt13:crit.high=5.15V:crit.low=4.85V:warn.high=5.10V:warn.low=4.9V
! 46: # hw.sensors.esm0.volt14=12.12 VDC (Power Supply 1 +12V)
! 47: hw.sensors.esm0.volt14:
! 48: # hw.sensors.esm0.volt15=3.32 VDC (Power Supply 1 +3.3V)
! 49: hw.sensors.esm0.volt15:
! 50: # hw.sensors.esm0.volt16=5.08 VDC (Power Supply 1 -5V)
! 51: hw.sensors.esm0.volt16:
! 52: # hw.sensors.esm0.volt17=12.20 VDC (Power Supply 1 -12V)
! 53: hw.sensors.esm0.volt17:
! 54:
! 55: # hw.sensors.esm0.volt18=5.09 VDC (Power Supply 2 +5V)
! 56: hw.sensors.esm0.volt18:crit.high=5.15V:crit.low=4.85V:warn.high=5.10V:warn.low=4.9V
! 57: # hw.sensors.esm0.volt19=12.07 VDC (Power Supply 2 +12V)
! 58: hw.sensors.esm0.volt19:
! 59: # hw.sensors.esm0.volt20=3.34 VDC (Power Supply 2 +3.3V)
! 60: hw.sensors.esm0.volt20:
! 61: # hw.sensors.esm0.volt21=5.01 VDC (Power Supply 2 -5V)
! 62: hw.sensors.esm0.volt21:
! 63: # hw.sensors.esm0.volt22=12.03 VDC (Power Supply 2 -12V)
! 64: hw.sensors.esm0.volt22:
! 65:
! 66: # hw.sensors.esm0.volt23=5.03 VDC (Power Supply 3 +5V)
! 67: hw.sensors.esm0.volt23:crit.high=5.15V:crit.low=4.85V:warn.high=5.10V:warn.low=4.9V
! 68: # hw.sensors.esm0.volt24=12.13 VDC (Power Supply 3 +12V)
! 69: hw.sensors.esm0.volt24:
! 70: # hw.sensors.esm0.volt25=3.34 VDC (Power Supply 3 +3.3V)
! 71: hw.sensors.esm0.volt25:
! 72: # hw.sensors.esm0.volt26=5.03 VDC (Power Supply 3 -5V)
! 73: hw.sensors.esm0.volt26:
! 74: # hw.sensors.esm0.volt27=11.97 VDC (Power Supply 3 -12V)
! 75: hw.sensors.esm0.volt27:
! 76:
! 77: # hw.sensors.esm0.volt28=5.02 VDC (System Power Supply +5V)
! 78: hw.sensors.esm0.volt28:
! 79: # hw.sensors.esm0.volt29=12.09 VDC (System Power Supply +12V)
! 80: hw.sensors.esm0.volt29:
! 81: # hw.sensors.esm0.volt30=3.32 VDC (System Power Supply +3.3V)
! 82: hw.sensors.esm0.volt30:
! 83: # hw.sensors.esm0.volt31=4.91 VDC (System Power Supply -5V)
! 84: hw.sensors.esm0.volt31:
! 85: # hw.sensors.esm0.volt32=11.82 VDC (System Power Supply -12V)
! 86: hw.sensors.esm0.volt32:
! 87: # hw.sensors.esm0.volt33=5.16 VDC (System Power Supply +5V aux)
! 88: hw.sensors.esm0.volt33:
! 89:
! 90: # hw.sensors.esm0.current0=2.30 A (Power Supply 1 +5V), OK
! 91: # hw.sensors.esm0.current1=0.90 A (Power Supply 1 +12V), OK
! 92: # hw.sensors.esm0.current2=1.50 A (Power Supply 1 +3.3V), OK
! 93: # hw.sensors.esm0.current3=1.90 A (Power Supply 2 +5V), OK
! 94: # hw.sensors.esm0.current4=0.90 A (Power Supply 2 +12V), OK
! 95: # hw.sensors.esm0.current5=1.50 A (Power Supply 2 +3.3V), OK
! 96: # hw.sensors.esm0.current6=1.30 A (Power Supply 3 +5V), OK
! 97: # hw.sensors.esm0.current7=0.90 A (Power Supply 3 +12V), OK
! 98: # hw.sensors.esm0.current8=1.50 A (Power Supply 3 +3.3V), OK
! 99:
! 100: # hw.sensors.esm0.indicator0=Off (Chassis Intrusion)
! 101: hw.sensors.esm0.indicator0:crit=Off
! 102: # hw.sensors.esm0.indicator1=On (Backplane SCSI A Connected)
! 103: hw.sensors.esm0.indicator1:crit=On
! 104:
! 105: # hw.sensors.esm0.indicator2=On (Power Supply 1 AC)
! 106: hw.sensors.esm0.indicator2:crit=On
! 107: # hw.sensors.esm0.indicator3=On (Power Supply 1 SW)
! 108: hw.sensors.esm0.indicator3:crit=On
! 109: # hw.sensors.esm0.indicator4=On (Power Supply 1 OK)
! 110: hw.sensors.esm0.indicator4:crit=On
! 111: # hw.sensors.esm0.indicator5=On (Power Supply 1 ON), OK
! 112: # hw.sensors.esm0.indicator6=Off (Power Supply 1 FFAN)
! 113: hw.sensors.esm0.indicator6:crit=Off
! 114: # hw.sensors.esm0.indicator7=Off (Power Supply 1 OTMP)
! 115: hw.sensors.esm0.indicator7:crit=Off
! 116:
! 117: # hw.sensors.esm0.indicator8=On (Power Supply 2 AC)
! 118: hw.sensors.esm0.indicator8:crit=On
! 119: # hw.sensors.esm0.indicator9=On (Power Supply 2 SW)
! 120: hw.sensors.esm0.indicator9:crit=On
! 121: # hw.sensors.esm0.indicator10=On (Power Supply 2 OK)
! 122: hw.sensors.esm0.indicator10:crit=On
! 123: # hw.sensors.esm0.indicator11=On (Power Supply 2 ON), OK
! 124: # hw.sensors.esm0.indicator12=Off (Power Supply 2 FFAN)
! 125: hw.sensors.esm0.indicator12:crit=Off
! 126: # hw.sensors.esm0.indicator13=Off (Power Supply 2 OTMP)
! 127: hw.sensors.esm0.indicator13:crit=Off
! 128:
! 129: # hw.sensors.esm0.indicator14=On (Power Supply 3 AC)
! 130: hw.sensors.esm0.indicator14:crit=On
! 131: # hw.sensors.esm0.indicator15=On (Power Supply 3 SW)
! 132: hw.sensors.esm0.indicator15:crit=On
! 133: # hw.sensors.esm0.indicator16=On (Power Supply 3 OK)
! 134: hw.sensors.esm0.indicator16:crit=On
! 135: # hw.sensors.esm0.indicator17=On (Power Supply 3 ON), OK
! 136: # hw.sensors.esm0.indicator18=Off (Power Supply 3 FFAN)
! 137: hw.sensors.esm0.indicator18:crit=Off
! 138: # hw.sensors.esm0.indicator19=Off (Power Supply 3 OTMP)
! 139: hw.sensors.esm0.indicator19:crit=Off
! 140:
! 141: # hw.sensors.esm0.raw0=2 (Chassis Fan Ctrl)
! 142: # hw.sensors.esm0.raw1=227 (Backplane Control)
! 143: # hw.sensors.esm0.raw2=8738 (Backplane Fan Control)
! 144: # hw.sensors.esm0.raw3=42498 (Fan Enclosure)
! 145:
! 146: # hw.sensors.esm0.drive0=online (Drive 0)
! 147: hw.sensors.esm0.drive0:crit=online
! 148: # hw.sensors.esm0.drive1=online (Drive 1)
! 149: hw.sensors.esm0.drive1:crit=online
! 150: # hw.sensors.esm0.drive2=unknown (Drive 2)
! 151: hw.sensors.esm0.drive2:crit=unknown
! 152: # hw.sensors.esm0.drive3=unknown (Drive 3)
! 153: hw.sensors.esm0.drive3:crit=unknown
! 154: # hw.sensors.esm0.drive4=online (Drive 4)
! 155: hw.sensors.esm0.drive4:crit=online
! 156: # hw.sensors.esm0.drive5=online (Drive 5)
! 157: hw.sensors.esm0.drive5:crit=online
! 158: # hw.sensors.esm0.drive6=unknown (Drive 6)
! 159: hw.sensors.esm0.drive6:crit=unknown
! 160: # hw.sensors.esm0.drive7=unknown (Drive 7)
! 161: hw.sensors.esm0.drive7:crit=unknown
! 162:
! 163: # hw.sensors.ami0.drive0=online (sd0), OK
! 164: # hw.sensors.ami0.drive1=online (sd1), OK
! 165: # hw.sensors.safte0.temp0=30.00 degC, OK
! 166: # hw.sensors.safte0.temp1=30.00 degC, OK
! 167: # hw.sensors.safte0.indicator0=On (Fan0), OK
! 168: # hw.sensors.safte0.indicator1=On (Fan1), OK
! 169: # hw.sensors.safte0.indicator2=On (Fan2), OK
FreeBSD-CVSweb <freebsd-cvsweb@FreeBSD.org>
![[BACK]](/icons/cvsweb/back.gif){kind=icon}
Return to sensorsd.conf CVS log ![[TXT]](/icons/cvsweb/text.gif){kind=icon}
![[DIR]](/icons/cvsweb/dir.gif){kind=icon}
Up to [local] / nagios / check_hw_sensors